Exactly How to Install a Bathtub: Set Up an Acrylic Bathtub as Well as Tub Surround
Exactly How to Install a Bathtub: Set Up an Acrylic Bathtub as Well as Tub Surround
Blog Article
What're your ideas concerning A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't specifically rocket science, but it does need strong plumbing, carpentry, and often, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the project can move rapidly; if you have to open a wall surface to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub and embeded in the brand-new one. Make sure you have qualified on your own for the work and fit trying it. Instead of employing a contractor to take over a halfway-completed task, it is better to think about using one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will certainly help you mount a new bath tub in your restroom if you have actually already acquired a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools and also material list must comprise the following:
Preparing for the Installment
First of all, the sustaining framework provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be quite bothersome because of the limited accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the needed setting. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bath tub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the supply of water and examine all joints and also new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as also check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the tub has actually been used at the very least once as this will certainly settle it right into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in area between the tap and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous type must be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a rigid seal, causing the water to permeate the wall between the bath as well as the tiling, causing difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can split fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that short article was valuable. Sharing is caring. Helping others is fun. Kudos for your time. Don't forget to come by our site back soon.
View Website
Report this page